DualGard™

A complete system including:
DualPipe™ (1″ diameter)
DualGard Bracket™
DualClip II™
DualClip III™
DualGard Splice
DualGard Endcaps
DualCollar™

DualGard
Product packages in boxes of 50 and cases of 200.

DualPipe™
Product packages in boxes of 17 and cases of 714.

DualGard Collar/End Cap Kit
Product packages in boxes of 30 and cases of 30.

DualClip II™
Product packages in boxes of 35 and cases of 140.

DualClip III™
Product packages in boxes of 25 and cases of 100.

Setscrews, flanged bolts and a screwgun bit tip are included in each box.

See our full line-up of clamps for detailed information and pricing.

To help you and your distributor design a DualGard system for your purposes, check out our Web-based calculator.

Note: Do not use DualGard with attachment spacing greater than 32" (81.3 cm). Custom DualGard, Splice and SnoClips™ are available for seam spacing greater than 32" (81.3 cm). Please inquire through a distributor.

Before You Start: S-5!® Mini attachment clamps are installed differently depending upon clamp model and seam style. Please see the installation instructions included with your clamps.

STEP 1: Preparing the assembly

It is recommended to pre-load the setscrews into each clamp and DualCollar™ prior to commencing installation. DualGard uses two S-5! Mini clamps at each pipe bracket location. One of these clamps should be fastened to the pipe bracket on what will become the upslope side. Verify which side of the standing seam the setscrews will be applied to, and keep this in mind when bolting them to the pipe brackets. Hand-tighten the M8 bolts attaching the clamps to the DualGard brackets.

Notice: When using S-5-U Mini or S-5-H90 Mini clamps on horizontal seams, clamps cannot be pre-attached to brackets.

Installation Tip: To ensure the brackets line up, it is advisable to use a string line. This is best achieved by measuring up from the eave at each end of the run you are working on. Install a clamp at either end, wrap a string line around each of these clamps and pull it tight. Install the remaining clamps along this string line and your brackets will align with one another.

STEP 2: Install the first row of S-5 Mini clamps

This row of clamps will support the downslope end of the DualGard bracket. Using the string line method outlined above to align the clamps, tighten each setscrew to the appropriate recommended torque specification. Set aside the M8 bolts provided with the clamps for use later. If utilizing S-5-U Mini or S-5-H90 Mini for horizontal seams, install the upslope clamps now.

STEP 3: Prepare pipe/bracket/clamp assembly

Slide the correct number of DualGard brackets onto the 8-foot pipes. Trim either one of the first two pipes so that the connection points between pipes do not align. On the first pipe and bracket assembly, a DualCollar should be fastened onto the top and bottom pipes no more than 7″ from the ends of the pipes, with the first DualGard bracket and clamp placed just outside of the collars. The maximum allowable cantilever for DualPipe™ is 6 inches; setting the DualCollars at 7″ allows for a 1″ gap between the collars and the first DualGard bracket to provide relief for thermal movement. On the last pipe and bracket assembly, a DualCollar should be slid onto the top and bottom pipes just inside of the last bracket and left loose at this point.

STEP 4: Attach the second row of S-5 Mini clamps with attached pipe brackets

Place the pre-assembled section of pipe and brackets on the roof, aligning each bracket with the clamps installed in step 2. Bolt the pipe bracket to the downslope clamp using the provided M8 bolts and a 1⁄2″ (13 mm) wrench or socket to the recommended torque specification of 156 inch-pounds (13 foot pounds). Tighten the setscrew on the upslope clamp, then tighten the bolt.

STEP 5: Splices

At the end of each section of pipe where it meets an adjoining section it will be necessary to install a pipe splice. Splices come inserted in the end of the 1″ pipe supplied by S-5! distributors. As each section of pipe is laid down, use the splice to connect the pipes creating an unbroken run of pipe. Splices should be staggered so that the connections on the top pipes do not align with the connections on the bottom pipes. Trim the first top pipe of the assembly so that the splice falls between a different set of DualGard brackets than the bottom pipe splice.

NOTE: S-5! splices are designed with a dimple at center to provide relief for thermal expansion.

STEP 6: Completing assembly and adding final components

Repeat steps 3, 4, and 5 until assembly is complete. As mentioned in step 3, the last pipe assembly should have collars placed just inside of the last bracket of the run. Once the last pipe and bracket assembly is in place, tighten the setscrews on the two collars. Be sure to leave 1″ of space between the collars and the bracket at both ends of the assembly to allow for thermal movement. DualGard assemblies should not exceed 100′ in length. If a longer run is necessary, finish the assembly at or before 100′ and begin a new assembly. At this point it may be necessary to trim the pipe so that it does not extend more than 6″ past the final bracket in the run. This is best achieved using a reciprocating or circular saw with a fine-tooth carbide tip blade. Finish the run by installing the end caps.

Don’t forget DualClips™!

The use of DualClips is recommended with the DualGard system. DualClip II™ and DualClip III™ are optional components that can be added to your S-5! DualGard™ snow retention system to further retard the migration of snow. DualClip II fits seams heights from 1″ to 1.5″. DualClip III fits seams 1-3/4″ to 3-1/4″. When seam spacing is ≤ 24″, one DualClip is used between each seam on the first row of snow retention. When seam spacing is >24″, two clips should be used.

S-5!® has the best snow retention system attachment solutions in the industry for exposed fastener roofs. Our extensive line of versatile and affordable brackets fit every shape and size of virtually every exposed fastened and corrugated roof on the market. S-5! brackets have been extensively tested for load-to-failure results and water tightness, and come with an industry-leading 25-year manufacturer warranty.

Strong enough for heavy-duty applications, our CorruBracket™ 100T or 500T is the perfect fit for attaching S-5!’s DualGard dual-pipe snow retention system to corrugated roofs.